Anyone have any solutions for this issue? You’d think it would just bridge over the entire hole, don’t know why it’s doing this. We’re at 195mm height here and I’d rather not run a support the entire height of the model just for this little nub.

Using version 2.6.1

Edit: Model in question https://www.thingiverse.com/thing:5551428. Not my own, but getting some fun things printed for the Spooky season

  • remotelove@lemmy.ca
    link
    fedilink
    English
    arrow-up
    8
    ·
    1 year ago

    Just insert a modifier in there like a cube or something. Anything that gives it a flat layer to print would work, I suppose.

    However, I really need to see the layers below and above that picture to see what is actually going on.

    • MrQuallzin@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      4
      ·
      1 year ago

      That’s what I ended up doing, thanks! Put in a 0.2mm disk right at the problem area, now I’ve got a nice clean bridge.

  • marcos@lemmy.world
    link
    fedilink
    English
    arrow-up
    3
    ·
    1 year ago

    There is that trick of making a layer or two with rectangular holes on the top of that cylindrical one.

      • marcos@lemmy.world
        link
        fedilink
        English
        arrow-up
        1
        ·
        1 year ago

        Yep, I didn’t know the name, thanks.

        But sacrificial bridges is a bit generic. It’s sacrificial bridges with a rectangle circumscribed on the hole cut from it.

    • max@feddit.nl
      link
      fedilink
      English
      arrow-up
      2
      ·
      1 year ago

      Woah, that is neat. Diagonal I would’ve thought of, but conic slicing is quite an ingenious idea.

    • IMALlama@lemmy.world
      link
      fedilink
      English
      arrow-up
      3
      ·
      1 year ago

      This is the answer with anything based on slic3r in my experience.

      Is this your model @op? If yes, you can add two rectangles to either side of the hole that are 0.25mm or so in height to serve as a built in bridge and trick the slicer.

      • MrQuallzin@lemmy.worldOP
        link
        fedilink
        English
        arrow-up
        4
        ·
        1 year ago

        Not my model (Added source to my post). That was a good idea, though. What I ended up doing (and can’t believe I didn’t think of it sooner. Been a long day…) is adding a 0.2mm disk right at the problem height and it’s looking good!

        • IMALlama@lemmy.world
          link
          fedilink
          English
          arrow-up
          2
          ·
          1 year ago

          I got the idea while building my Voron - the designers bake a lot of tricks like this into their files. I’ve adopted a lot of them to improve printability and am happy to share the knowledge!

  • Dogrunner@lemmy.world
    link
    fedilink
    English
    arrow-up
    1
    ·
    edit-2
    1 year ago

    It looks like you already found a solution, but to be honest: I wanted to help you out, but the model is just 100mm high. If you are at 195mm height, I couldn’t even reproduce your issue. I looked around to find a hole similar to the screenshot, but haven’t found it. Looked through the layers but haven’t found any of mid-air prints :(

    • MrQuallzin@lemmy.worldOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      Printed at 200% (So 200mm tall in total). 195mm was just that layer’s height. Who knows what little setting was making it be like that.